The online cutting data calculator FRAISA ToolExpert® HelixRamp

With the new high-performance penetration edge, the NX-NVDS and NB-NVDS achieve a level of performance that facilitates peak productivity and process reliability in 7 dimensions!

Toolexpert Helixramp

This FRAISA innovation gives NVDS tools a ground-breaking performance range!

The development of the new penetration edge allows FRAISA to introduce the term high-performance penetration. The new high-performance penetration edge cuts easily and clears the chips without disrupting the process.

The cutting data software FRAISA ToolExpert HelixRamp was developed for the new high-performance tools.

The software can conveniently be started using the FRAISA website. With just a few clicks, you can defi ne the material, tool and penetration strategy, and receive the parameters to be programmed for your machine control or CAM system.

Use the online cutting data calculator FRAISA ToolExpert HelixRamp without having to download any software!

Start FRAISA ToolExpert® HelixRamp


Program the penetration angle φZ or φA correctly!

Penetration using helical interpolation is today used as standard to get into pockets, deeper levels or bores. The reason for this is the improved chip removal and the lower process temperatures during helical interpolation. This allows higher penetration depths to be achieved during helical machining. Depending on the machine control system or CAM system used, different input parameters may be required for the same procedure. Typically these are:

  • The external diameter of the helical drilling DA
  • The central penetration angle φZ
  • The speed n and the feed rate vfZ at the center
  • The penetration depth TB

FRAISA recommends entering the DA as 1.9xd1 if possible. e.g.: milling cutter diameter d1 = 10 mm, DA = 19 mm

ATTENTION: For cycle programming, it may be necessary to enter other penetration parameters, depending on the machine control system. On some machine control systems (e.g. Heidenhain), it is not the central penetration angle φZ that is needed, but the penetration angle at the outer track φA!

This is entered at the machine (tool table) under “Angle“. The penetration angles at the center φZ and at the outer track φA vary signifi cantly, depending on the DA for the milling cutter diameter. The outer angle φA is always smaller than the central angle φZ.

With other control systems again, the infeed per helical rotation (ap/360°), the radius of the tool tip path (e.g. Siemens) or the radius of the bore (e.g. Fanuc) is required.

In some cases the ramps have to be selected on the basis of the component, e.g. an elongated hole slot. The parameters for programming a ramp are identical on all control systems.

Helix Penetration Process

Helix Penetration Process

Use FRAISA ToolExpert HelixRamp

For the cycle programming on the machine, note which entries are relevant for the corresponding control system.
For the cutting data, you can fi nd the basic data with φZ and vfZ. You can then use the conversion table below to fi nd φA. It is even faster and simpler with the cutting data software ToolExpert HelixRamp, which allows all penetration parameters to be calculated and compared with just a few clicks!

Conversion table

Downloads

downloads
Product catalog
High-performance milling cutter NVDS
Product brochure

Do you have questions about our products?
We will be happy to help!

FRAISA SA

Gurzelenstrasse 7
CH-4512 Bellach
Schweiz

Tel.: +41 (0)32 617 42 42
E-Mail: mail.ch@fraisa.com

FRAISA GmbH

Hanns-Martin-Schleyer-Str. 15b
D-47877 Willich
Deutschland

Tel.: +49 (0)2154 489 84-0
E-Mail: info.de@fraisa.com

FRAISA Sarl.

7, Rue de Lombardie
ZA Les Pivolles
F-69150 Décines

Tel.: +33 (0)4 72 14 57 00
E-Mail: fraisa@fraisa.fr

FRAISA Italia s.r.l.

Via Grosio 10/8
I-20151 Milano
Italia

Tel.: +39 02 33406 086
E-Mail: info.it@fraisa.com

FRAISA Hungária Kft.

Vásárhelyi Pál utca 3
H-3950 Sárospatak
Hungária

Tel.: +36 47 312 686
E-Mail: info@fraisa.hu

FRAISA USA, Inc.

1265 Grey Fox Road, Suite 600
Arden Hills, MN 55112
USA

Tel.: +1 (651) 636-8488
E-Mail: info.us@fraisa.com

FRAISA (Shanghai) Co., Ltd

A202, Building 3, No.526,
3rd East Fute Road
Shanghai Pilot Free Trade Zone
Shanghai 200131
P.R.China

Tel.: +86 21 5820 5550
E-Mail: infochina@fraisa.com

Please contact me by e-mail.

Form fields with an * are mandatory

Please read our privacy statement.

cron